Volvo D12 Spezifikationen

Volvo Trucks North America, Inc.Greensboro, NC USADate Group No. Supp. Page8.2003 215 001 1(21)TSIThis TSI Service Bulletin replaces TSI Service Bulle

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 10(21)22T2006777Fig. 13: Tightening rocker arm shaft and camshafttogetherW20035

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 11(21)25Clean the contact surfaces for the upper timing gearcover. Install a ne

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 12(21)29Rotate the camshaft until the cam sensor wheel toothaligns with the cam

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 13(21)•Use the portion of the pointer that is fastened to thetool shaft as a re

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 14(21)12T2012262Fig. 16: Installing camshaft alignment toolInstall camshaft ali

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 15(21)18Install the front cover positioning tool, J–41272. Tightenbolts to alig

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 16(21)24T2007003Fig. 18: Valve cover tightening sequenceInstall the valve cover

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 17(21)30Run the engine until the coolant reaches operatingtemperature. Allow to

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 18(21)2154-06-03-02Camshaft Timing, Check and AdjustYou must read and understan

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 19(21)3W2003738Fig. 19: Rotating the flywheel to 0 TDCA Opposite direction of e

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 2(21)ToolsSpecial ToolsThe following special tools are used to replace or repai

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 20(21)6W2002245T2008255Insert two 0.10 mm (0.004 in.) feeler gauges on the load

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 21(21)9W2002245Tighten the bolts an additional 120 ± 5 per the torquesequence s

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 3(21)Service Procedures2154-03-02-01Camshaft, Replacement(With EPG or VEB)You m

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 4(21)3Remove the upper timing gear cover.4T2006672T2008251Remove the inspection

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 5(21)6T2007095Fig. 3: Bolts holding the idler gear in placeRemove the adjustabl

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 6(21)8T2006777Fig. 4: Removing the rocker arm shaft assembly boltsW2000937Fig.

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 7(21)10T2007148Fig. 7: Tool 9998270 installedInstall camshaft counterhold tool

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 8(21)Installation15Position the camshaft bearing housings on the cylinderhead b

Volvo Trucks North America, Inc. Date Group No. PageTSI 8.2003 215 001 9(21)18T2007148Fig. 11: Installing the camshaft drive gearInstall the camshaft